ALITOVE DC 24V 15A 360W Power Supply Universal Regulated Switching Transformer Adapter LED Driver 110V/220V AC Input for LED Strip CCTV Radio

Very easy to use! Flip the plastic guard up, screw down your two wires for AC in, and boom! You've got a ton of 24 volt power to work with! Fan is on but quite above ~20-40 watts. Above ~100 you can start to hear it pretty good though. Above 300 watts, and yeah, it's a bit loud 😂 but not terrible by any means. Unit is warm up to about 200 watts. Above that, it's hot. But not detrementally so from my measurements. Voltage has a adjustment knob for +/- 5% control, but I'm not doing anything that sensitive. It does work however. Seems to have very decent under-voltage-lockout/short circuit protection. And will cut power in the event of a short, or just before hitting the rated power limit. No issues there! Amazing bang for your buck. Compaired to the plastic 1-2 amp power bricks, this is just a no Brainer. Significantly improved heat disaption should improve longevity for the output capacitors, much beefier and efficient forward-converter vs a flyback. And very little switching nosie/voltage sag on the output, even under a decent load.

I bought two of these 24V units to power a decent sized COB LED strip installation in my kitchen. I also bought three 5V units to power a BUNCH of RGBIC LED strips, two hooked up to a switched circuit, and one always on. The 24V units are on a separate switch. So far all of the power supplies in the installation work great, only complaint is that the fans get noisy on the 24V units after the lights have been on for about five minutes. My complaint about the fans really has to do with one of the power supplies which turns its fan on-off-on-off to regulate the temperature of the power supply depending on how heavy the electric load is, while the second one has a smooth speed control on its fan and ramps the speed up or down to keep its temperature controlled. I much prefer the self-adjusted fan that runs at much lower RPMs than the power supply that turns its fan on and off, because that one turns the fan on full-speed and makes much more noise, and brings attention to the fan noise by constantly turning it on and off. I’m planning to move both of the 24V supplies to a location away from the kitchen so that the fans can’t be heard at all. The voltage measures clean on both, and the output is adjustable so you can dial in exactly the voltage you need for the application you are connecting it to. The voltage is well regulated as well. Great little power supplies at an affordable price. Highly recommended.

Installed this unit in our pantry. Instructions were very clear and easy to understand. The unit has a fan and kicks on if the lights have been left on for a while. The fan is quiet as well. In my opinion, this is a quality built adapter and we are very happy with the performance.

Used this 24 volt power supply to power my outdoor lighting.

I bought this power supply to recharge my LiPo batteries using it to power my Lipo charger. The batteries charged by this power supply are 3s 3000mAh Lipo's now & it does a great job only drawing 20% of the power supply output. When charging larger batteries or battery packs, there is plenty of room for the power supply to increase output without going over the magic 80% of the power supply total output. I should have tried this years ago, but it wasn't known to me @ that time. This is a great deal for my needs & hopefully it will last for many years. By the end of July in the same year I bought it, the fan no longer operates. The fan will run on outside power showing that it is still good, but the thermistor that controls it has gone bad. The unit still puts out good clean power.

Do not buy! Replaced dead power supply in my older 3d printer with this (volt and wattage matched old) and worked fine-ish for 6 months... But the printer always had problems getting enough power to keep the hotend at temp when the cooling fan would kick on, and then last night mid-print this supply died. Seems the resistor next to the "fuse" blew up. See attached picture. I especially love the part where the 250v 8 amp "fuse" has melted, and that the silkscreening clearly says "250v 6.3a"

Needed for one for an Ender 3 3d printer, Easy to install, direct fit. Now it works.

I can attest that if you don't run this power supply with adequate airflow and/or push it to its rated 15 amp stated capacity to much, it seems to cut the power supply rated lifetime in half. Mine lasted 1.5 years before dying when using it in a 3D printer occasionally. I got about 3000 hours in when it died. I gave it 3 stars because I'm not sure if the fault was also related to one of the case cooling fans providing cooling to the electronic section died as well.

The two I bought lasted about five minutes

Alles perfekt gelaufen. Ich baue mir einen Reifeschrank